معلومات عامة
Description
LLDPE, or Linear Low-Density Polyethylene, is a type of polyethylene that is similar to LDPE in its flexibility, but with better performance properties. It has a higher molecular weight and less branching than LDPE, which gives it better strength, impact resistance, and heat resistance. LLDPE is commonly used in applications where these properties are important, such as in packaging, films, and blown or injection-moded parts. It is also recyclable, which makes it an environmentally-friendly choice.
Applications
Some typical applications for LLDPE:
- Packaging: Films, bags, and coatings for food, beverages, and industrial chemicals
- Blown and injection-molded parts: Automotive parts, appliance parts, and industrial components
- Extrusion: Film, pipe, and sheet applications
- Medical: Blood bags, IV fluid bags, and medical tubing
- Agricultural: Irrigation tubing, greenhouse films, and silage bags
- Transportation: Bus interiors, fuel tanks, and automotive parts
- Wire and cable insulation: Telecommunications and power cables
الدرجات
الدرجات المتاحة: 69 (إزالة المرشحات)
Density 918 kg/m3, MFR(2.16 kg) 1.0 g/10 min 118LJ is a butene Linear Low Density Polyethylene TNPP free grade suitable for general‐purpose blown films medium gauge. Films produced from these resins are tough with excellent puncture resistance, high tensile strength and good hot tack properties. AmericasAsiaEuropeGreater ChinaMEA
Density 918 kg/m3, MFR (2.16 kg) 1.0 g/10 min SABIC® LLDPE 118NE is a butene linear low density polyethylene resin typically used for general purposeapplications. Films produced from this resin are tough with good puncture resistance, high tensile strength, good hottack properties and low gel levels. Application Typical applications for SABIC® LLDPE 118NE are shipping sacks, ice bags, frozen food bags, liners, carrier bags, garbage bags, agriculture films, lamination and coextruded films, shrink film (for blending with LDPE), industrial consumer packaging and high clarity film if blended with (10-20%) LDPE. Film properties Film of 50 μm and BUR=2 has been produced on Kiefel IBC with 140 kg/h. Die size 200 mm, die gap 2,7 mm. This product is not intended for and must not be used in any pharmaceutical/medical applications. AmericasAsiaEuropeGreater ChinaMEA
Density 918 kg/m3, MFR(2.16 kg) 1.0 g/10 min SABIC® LLDPE 118NJ is a butene linear low density polyethyleneresin typically used for general purpose applications. Films produced from this resin are tough with good puncture resistance, high tensile strength and good hot tack properties. 118NJ is TNPP free and it does not contain slip and antiblock additive. AmericasAsiaEuropeGreater ChinaMEA
Density 918 kg/m3, MFR(2.16 kg) 1.0 g/10 min SABIC® LLDPE 118P is a butene linear low density polyethylene resin typically used for food applications. It contains an antioxidant inspired by nature offering advantages versus conventional stabilizers: - Produced with no phosphorus or sulphur based additives - Improved processing stability at a much reduced concentration - No Specific Migration Limit (SML free) Films produced from this resin typically have good puncture resistance, high tensile strength, good hot tack properties and low gel levels. Typical applications for SABIC® LLDPE 118P are (frozen) food bags and lamination films. Film properties. Film of 50 μm and BUR=2 has been produced on Kiefel IBC with 140 kg/h. Die size 200 mm, die gap 2,7 mm. This product is not intended for and must not be used in any pharmaceutical/medical applications. AmericasAsiaEuropeGreater ChinaMEA
Density 918 kg/m3, MFR (2.16 kg) 1.0 g/10 min SABIC® LLDPE 118WE is a butene-linear low density polyethylene resin for general purpose applications. Films produced from this resin are tough with excellent puncture resistance, high tensile strength, good hottack properties and low gel levels. The resin contains anti block and slip agent. Application Typical applications for SABIC® LLDPE 118WE are shipping sacks, ice bags, frozen food bags, liners, carrier bags, garbage bags, agriculture films, lamination and coextruded films, shrink film (for blending with LDPE), industrial consumer packaging and high clarity film if blended with (10-20%) LDPE. Film properties Film of 50 μm and BUR=2 has been produced on Kiefel IBC with 140 kg/h. Die size 200 mm, die gap 2,7 mm. The product mentioned AmericasAsiaEuropeGreater ChinaMEA
Density 918 kg/m3, MFR(2.16 kg) 1.0 g/10 min SABIC® LLDPE 118WJ is a butene linear low density polyethylene resin typically used for general purpose applications. Films produced from this resin are tough with good puncture resistance, high tensile strength and good hottack properties. The resin contains slip and antiblock additive. SABIC® LLDPE 118WJ is TNPP free. This product is not intended for and must not be used in any pharmaceutical/medical applications. AmericasAsiaEuropeGreater ChinaMEA
Density 918 kg/m3, MFR(2.16 kg) 1.0 g/10 min 118WSJ is a butene Linear Low Density Polyethylene TNPP free grade suitable for general‐purpose packaging with high clarity thin gauge film. Films produced from these resins are tough with excellent puncture resistance, high tensile strength and good hot tack properties. AmericasAsiaEuropeGreater ChinaMEA
Density 918 kg/m3, MFR(2.16 kg) 1.0 g/10 min 118ZJ is a butene Linear Low Density Polyethylene TNPP free grade suitable for general‐purpose blown films medium gauge. Films produced from these resins are tough with excellent puncture resistance, high tensile strength and good hot tack properties. AmericasAsiaEuropeGreater ChinaMEA
Density 920 kg/m3, MFR(2.16 kg) 1.4 g/10 min SABIC® 120NT is an ethylene-butene copolymer designed for blown film application. 120NT contains no slip and no antiblock. Asia
Density 918 kg/m3, MFR(2.16 kg) 1.0 g/10 min 120WJ is a Linear Low Density Polyethylene TNPP free grade suitable for general purpose packaging. Films produced using these resins gives good tensile properties, impact strength and excellent optical properties. 120WJ contains slip and antiblock additive. AmericasAsiaEuropeGreater ChinaMEA
Density 918 kg/m3, MFR(2.16 kg) 1.0 g/10 min 121WJ is a high quality Linear Low Density Polyethylene TNPP free grade for blown film. It has excellent processability and films produced from this resin have good clarity, excellent puncture resistance, high tensile strength and good sealing characteristics. 121WJ contains slip and antiblock additive. AmericasAsiaEuropeGreater ChinaMEA
Density 928 kg/m3, MFR(2.16 kg) 1.0 g/10 min 128CNJ is a Linear Low Density Polyethylene natural resin designed for extrusion applications. This grade is combining stiffness, toughness, high melt strength with an excellent processability due to its broad molecular weight distribution. It is TNPP free and contains an optimized level of stabilizers and does not contain any slip or anti-block additives. AmericasAsiaEuropeGreater ChinaMEA
218B 218B AmericasAsiaEuropeGreater ChinaMEA
Density 918 kg/m3, MFR (2.16 kg) 2.0 g/10 min SABIC® LLDPE 218BE is a butene linear low density polyethylene resin with an additive package typically designed for a broader range of food applications (TNPP free). The good thermal stability allows to use the resin in critical extrusion processing conditions. Application SABIC® LLDPE 218BE is typically used for food applications (lamination film, barrier film) but can also be used in industrial packaging and as blending partner with other SABIC® PE resins in both blown and cast film applications. The product mentioned herein is in particular not tested and therefore not validatedfor use in pharmaceutical/ medical applications. AmericasAsiaEuropeGreater ChinaMEA
Density 918 kg/m3, MFR(2.16 kg) 2.0 g/10 min SABIC® LLDPE 218BJ is a butene linear low density polyethylene resin with an additive package typically designed for a broader range of food applications (TNPP free). The good thermal stability allows to use the resin in critical extrusion processing conditions. Films produced from SABIC® LLDPE 218BJ have better draw-down ability compared to lower MFR LLDPE resins. This product is not intended for and must not be used in any pharmaceutical/medical applications. AmericasAsiaEuropeGreater ChinaMEA
Density 0.918 kg/m3, MFR(2.16 kg) 2.0 g/10 min 218NJ is a butene Linear Low Density Polyethylene TNPP free grade suitable for general‐purpose packaging. It is easy to process giving good tensile properties, impact strength and optical properties. 218NJ contains no slip and no antiblock additives. AmericasAsiaEuropeGreater ChinaMEA
Density 920kg/m3, MFR (2.16 kg) 2 g/10 min SABIC® LLDPE 218NM is a butene linear low density polyethylene resin typically used for general purpose applications and also suitable for blending with conventional LDPE. Film made from LLDPE 218NM exhibit a good puncture resistance, high tensile strength and good hot tack properties AmericasAsiaEuropeGreater ChinaMEA
Density 918 kg/m3, MFR(2.16 kg) 2 g/10 min SABIC® 218NT is an ethylene-butene copolymer designed for blown film application. It has excellent stiffness, puncture resistance, high tensile strength and sealing property, 218NT contains no slip and no antiblock Asia
Density 918 kg/m3, MFR(2.16 kg) 2.0 g/10 min 218WJ is a butene Linear Low Density Polyethylene TNPP free grade suitable for general‐purpose packaging. It is easy to process giving good tensile properties, impact strength and optical properties. 218WJ contains slip and antiblock additives. AmericasAsiaEuropeGreater ChinaMEA
Density 920 kg/m3, MFR(2.16 kg) 2 g/10 min SABIC® 220HT is an ethylene-butene copolymer designed for blown film application. It has excellent stiffness, puncture resistance, high tensile strength, High clarity and high gloss. 220HT contains no slip and no antiblock. Asia
Density 920 kg/m3, MFR(2.16 kg) 2.4 g/10 min SABIC® 220NT is an ethylene-butene copolymer designed for blown film & cast film application. 220NT contains no slip and no antiblock. Asia
Density 920 kg/m3, MFR(2.16 kg) 2.0 g/10 min SABIC® 220WT is an ethylene-butene copolymer designed for blown film application. It has excellent stiffness, puncture resistance, high tensile strength, High clarity and high gloss. 220WT contains high slip and high antiblock. Asia
Density 921 kg/m3, MFR(2.16 kg) 1.9 g/10 min SABIC® 221WT is an ethylene-butene copolymer designed for blown film application. 221WT has Superior film mechanical property like stiffness, puncture resistance and tensile strength, it also has excellent sealing property. 221WT contains high slip and high antiblock. Asia
SABIC® LLDPE318B is a standard C4-LLDPE grade with a relatively low melt flow rate. SABIC® LLDPE318B is a standard C4-LLDPE grade with a relatively low melt flow rate. SABIC® LLDPE318B is a general grade, typically used for low filled or additive masterbatches in film and blow moulding applications(e.g. slip agents, anti fog agents, anti static agents, thermal stabilizers). This product is not intended for and must not be used in any pharmaceutical/medical applications. AmericasAsiaEuropeGreater ChinaMEA
Density 918 kg/m3, MFR (2.16 kg) 2.8 g/10 min SABIC® LLDPE 318BE is a butene linear low density polyethylene resin typically designed for easy processing and specially formulated for optimum thermal stability at high temperatures used in cast film extrusion. Cast film produced from SABIC® LLDPE 318BE exhibit very good optical properties, puncture resistance and tear strength. Application SABIC® LLDPE 318BE resin is typically used for hand and pallet stretch wrap. Film properties Properties are determined on 20 μm cast stretch film produced on a 2 m commercial cast stretch line: melt temperature 270 °C, chill roll temperature 20 °C and line speed of 450 m/min. Processing conditions SABIC® LLPDE 318BE is extrudable with conventional cast film extrusion equipment. Minor machine modifications may be required for optimum use. Cast film melt temperatures 250 - 300 °C. This product is not intended for and must not be used in any pharmaceutical/medical applications. AmericasAsiaEuropeGreater ChinaMEA
Density 918 kg/m3, MFR(2.16 kg) 2.8 g/10 min SABIC® LLDPE 318BJ is a butene linear low density polyethylene resin typically designed for easy processing and specially formulated for optimum thermal stability at high temperatures used in cast film extrusion. Cast film produced from SABIC® LLDPE 318BJ exhibit excellent optical properties, puncture resistance and tear strength .SABIC® LLDPE 318BJ is TNPP free. This product is not intended for and must not be used in any pharmaceutical/medical applications. AmericasAsiaEuropeGreater ChinaMEA
Density 918 kg/m3, MFR(2.16 kg) 2.8 g/10 min 318CNJ is a Linear Low Density Polyethylene TNPP free grade designed for wire and cable applications. It contains optimized level of antioxidants and does not contain any slip and antiblock additives. Sufficient antioxidant and Cu-inhibitor should be added to meet specific ageing requirements. For jacketing applications, addition of Carbon Black or UV stabilizer is required. AmericasAsiaEuropeGreater ChinaMEA
Density 920 kg/m3, MFR(2.16 kg) 2.8 g/10 min SABIC® 320BT is an ethylene-butene copolymer designed for wire and cable application. 320BT contains high antioxidant, no slip and no antiblock. Asia
Density 920 kg/m3, MFR(2.16 kg) 2.8 g/10 min SABIC® 320NT is an ethylene-butene copolymer designed for wire and cable application. it is designed for high speed cable extrusion line, product use 320NT has excellent cable outlook, compare to the other polyethylene, 320NT is designed to reduce the use of additive during compounding, suggest the customer to optimize the silane and peroxide amount for 320NT based material, suitable for one-step silane crosslinking low voltage power cable insulation. 320NT contains no slip and no antiblock. Asia
Density 924 kg/m3, MFR (2.16 kg) 3.6 g/10 min SABIC® LLDPE 324CE is a Linear Low Density Polyethylene natural resin typically used for wire and cable applications. SABIC® LLDPE 324CE contains a low level of antioxidants and does not contain any antiblock and/or slip agents. It also exhibits good Environmental Stress Crack Resistance (ESCR). Sufficient Cu-inhibitor should be added to meet specific ageing requirements. For jacketing applications, addition of Carbon Black or UV stabilizer is required. Applications - Telecommunication and Power cable (LV, MV, HV) jacketing. - Halogen-free flame retardant (HFFR) compounds. - One-step or two-steps silane crosslinkable for cable insulation. This product is not intended for and must not be used in any pharmaceutical/medical applications. Mechanical and electrical properties. Test specimens were prepared by compression moulding according to ASTM D 4703. AmericasAsiaEuropeGreater ChinaMEA
Density 924 kg/m3, MFR(2.16 kg) 3.6 g/10 min 324CNJ is a Linear Low Density Polyethylene TNPP free grade designed for wire and cable applications. It contains low level of antioxidants and does not contain any slip and antiblock additives. Sufficient antioxidant and Cu-inhibitor should be added to meet specific ageing requirements. For jacketing applications, addition of Carbon Black or UV stabilizer is required. AmericasAsiaEuropeGreater ChinaMEA
Density 930 kg/m3, MFR (4.2 kg) 0.33 g/10 min SABIC® LLDPE 430BE is a butene linear low density polyethylene resin. The material, natural resin, is typically used for cast film applications, offering good mechanically properties, stiffness enhancement and furthermore enables to gain high line speeds. SABIC® LLDPE 430BE is provided with a dedicated anti oxidant package suitable for cast film extrusion with low gel levels. Applications Skin layers for non-cling stretch cast film, cast film side encapsulation, mid layer hygienic cast film and product to realize downgauging by stiffness enhancement. Film properties Properties are determined on 20 μm cast stretch film produced on a 2 m commercial cast stretch line: melt temperature 270 °C, chill roll temperature 20 °C and line speed of 450 m/min. Processing conditions SABIC® LLDPE 430BE is extrudable with conventional cast film extrusion equipment. Minor machine modifications may be required for optimum use. Cast film melt temperatures 250 - 300 °C. This product is not intended for and must not be used in any pharmaceutical/medical applications. AmericasAsiaEuropeGreater ChinaMEA
SABIC® LLDPE 518N is a butene linear low density polyethylene resin. SABIC® LLDPE 518N is a butene linear low density polyethylene resin. Films produced from this resin have high toughness,good puncture resistance, good heat sealing behaviour and excellent machinability on conversion lines. Typical applications for SABIC® LLDPE518N are heavy duty shipping sacks, ice bags, frozen food bags, potato bags and agriculture films. Film properties: Film of 50 µm and BUR=2 has been produced on Kiefel IBC with 130 kg/h. Die size 200 mm, die gap 2,7 mm. This product is not intended for and must not be used in any pharmaceutical/medical applications. AmericasAsiaEuropeGreater ChinaMEA
Density 918 kg/m3, MFR(2.16 kg) 0.5 g/10 min SABIC® LLDPE 518NJ is a fractional melt-index butene linear low density polyethylene resin. Films produced from this resin have high toughness, good puncture resistance, good heat sealing behaviour and excellent machinability on conversion lines. This grade is TNPP free. AmericasAsiaEuropeGreater ChinaMEA
Density 918 kg/m3, MFR(2.16 kg) 0.5 g/10 min SABIC® 518NT is an ethylene-butene copolymer designed for blown film application. It has excellent mechanical strength, puncture resistance, high tensile strength and sealing property. 518NT contains no slip and no antiblock. 518NT contains no slip and no antiblock. Asia
Density 918 kg/m3, MFR (2.16 kg) 0.9 g/10 min SABIC® LLDPE 6118NSF is a hexene linear low density polyethylene resin. Films made from this resin exhibit goodtensile strength, stiffness, dart drop impact strength,tear strength and seal/hottack properties. Application: Typical application for SABIC® LLDPE 6118NSF are heavy duty bags, lamination films, agriculture films, stretch wrap films, frozen food packaging and other applications requiring higher impact strength, high tear resistance and improved sealing properties.Film properties: Film of 50 µm and BUR = 2 has been produced on Kiefel IBC with 140 kg/h. Die size 200 mm, die gap 2.7 mm.This product is not intended for and must not be used in any pharmaceutical/medical applications. AmericasAsiaEuropeGreater ChinaMEA
SABIC® LLDPE 6218Bis a hexene-linear low density polyethylene. SABIC® LLDPE 6218Bis a hexene-linear low density polyethylene. ApplicationTypical application for SABIC® LLDPE6218B Film propertiesFilm of 50 µm with BUR=2 is produced on Kiefel IBC with 140 kg/h. Die size 200 mm, die gap 1.8 mm.The product mentioned herein is in particular not tested and therefore not validated for use in pharmaceutical/ medical applications. AmericasAsiaEuropeGreater ChinaMEA
Density 920 kg/m3, MFR (2.16 kg) 2.2 g/10 min SABIC® LLDPE 6218BE is a hexene linear low density polyethylene resin for cast film applications. The product has been specially formulated for optimum thermal stability at high temperatures used in cast film extrusion. Cast films produced from SABIC® LLDPE 6218BE exhibit good optical properties, improved toughness, puncture resistance and tear strength. Application SABIC® LLDPE 6218BE resin is typcially used for pallet stretch wrap (pre-stretch), high performance draw down films and other mono layer and coextruded film applications where high strength is required. The grade is also suggested for blending with ethylene/butene copolymer LLDPE and LDPE for improving strength. Film properties Properties are determined on 20 μm cast stretch film produced on a 2 m commercial cast stretch film line: melt temperature 270 °C, chill roll temperature 20 °C and a line speed of 450 m/min. Processing conditions SABIC® LLDPE 6218BE is extrudable with conventional cast film extrusion equipment. Temperatures 250- 300 °C. This product is not intended for and must not be used in any pharmaceutical/medical applications. AmericasAsiaEuropeGreater ChinaMEA
Density 918 kg/m3, MFR(2.16 kg) 2.8 g/10 min 6318BJ resin is a hexene comonomer based Linear Low Density Polyethylene TNPP free grade designed to provide easy processability and specially formulated for optimum thermal stability at high processing temperatures used during production of Cast films. Films produced using this resin gives excellent optical properties, toughness, puncture resistance and tear strength. AmericasAsiaEuropeGreater ChinaMEA
Density 920 kg/m3, MFR (2.16 kg) 3.2 g/10 min SABIC® LLDPE 6318BE is a hexene linear low density polyethylene resin for cast film applications. The product has been specially formulated for optimum thermal stability at high temperatures used in cast film extrusion. Films produced from this grade exhibit good optical properties, toughness, puncture resistance and tear strength. Application SABIC® LLDPE 6318BE resin is typically used for pallet stretch wrap (pre-stretch), high performance draw down films and other mono layer and coextruded film applications where high strength is required. The grade is also suggested for blending with ethylene/butene copolymer LLDPE and LDPE for improving strength. Film properties Properties are determined on 20 μm cast stretch film produced on a 2 m commercial cast stretch line: melt temperature 270 °C, chill roll temperature 20 °C and line speed 450 m/min. Processing conditions SABIC® LLDPE 6318BE is extrudable with conventional cast film extrusion equipment. Temperatures 250- 300°C. This product is not intended for and must not be used in any pharmaceutical/medical applications. AmericasAsiaEuropeGreater ChinaMEA
Density 918 kg/m3, MFR(2.16 kg) 2.8 g/10 min 6318BJ resin is a hexene comonomer based Linear Low Density Polyethylene TNPP free grade designed to provide easy processability and specially formulated for optimum thermal stability at high processing temperatures used during production of Cast films. Films produced using this resin gives excellent optical properties, toughness, puncture resistance and tear strength. AmericasAsiaEuropeGreater ChinaMEA
Density 935 kg/m3, MFR (2.16 kg) 2.8 g/10 min SABIC® LLDPE 6335BE is a hexene linear low density polyethylene resin for cast film applications. The product has been specially formulated for optimum thermal stability at high temperatures used in cast film extrusion. Cast films produced from SABIC® LLDPE 6335BE exhibit excellent optical properties, toughness, puncture resistance, tear strength and stiffness. Application SABIC® LLDPE 6335BE resin is recommended for use in non cling layers in pallet stretch wrap (pre-stretch), high performance draw down films and other mono layer and coextruded film applications where high strength is required. Film properties Properties are determined on 20 μm cast stretch film produced on a 2 m commercial cast stretch film line: melt temperature 270 °C, chill roll temperature 20 °C and line speed 450 m/min. Processing conditions SABIC® LLDPE 6335BE is extrudable with conventional cast film extrusion equipment. Minor machine modification may be required for optimum use. Cast film melt temperatures 250 - 300 °C. The product mentioned herein is in particular not tested and therefore not validated for use in pharmaceutical/ medical applications. AmericasAsiaEuropeGreater ChinaMEA
Density 921 kg/m3, MFR (2.16 kg) 0.8 g/10 min SABIC® LLDPE 6821NE is a hexene linear low density polyethylene. Films made from this resin exhibit good tensile strength, stiffness, dart drop impact strength, tear strength and hottack properties. Application Typical applications for SABIC® LLDPE 6821NE are heavy duty bags, lamination films, agriculture films, stretch wrap films, frozen food packaging and other applications requiring high impact strength and tear resistance. Film properties Film of 50 μm and BUR = 2 has been produced on Kiefel IBC with 140 kg/h. Die size 200 mm, die gap 2.7 mm. This product is not intended for and must not be used in any pharmaceutical/medical applications. AmericasAsiaEuropeGreater ChinaMEA
Density 921 kg/m3, MFR(2.16 kg) 0.8 g/10 min 6821NJ is a fractional melt index hexene copolymer based Linear Low Density Polyethylene TNPP free grade suitable for high strength packaging applications. Films produced using this resin gives outstanding toughness, excellent puncture resistance, good sealing characteristics and tear resistance. 6821NJ contains no slip and no antiblock additive. AmericasAsiaEuropeGreater ChinaMEA
SABIC® LLDPE 726N is abutene linear low density polyethylene resin. SABIC® LLDPE 726N is abutene linear low density polyethylene resin.This grade is typically designed to give blown films a relatively high stiffness for good machinability and a good overall balance of other performance properties, such as puncture resistance, impact strength and heat sealability. Typical applications for SABIC® LLDPE 726N are shipping sacks, produce bags, can liners and carrier bags. SABIC® LLDPE 726N has good optical properties when blended with a LDPE (15-85%). Film properties: Film of 50 µm and BUR=2 has been produced on Kiefel IBC with 130 kg/h. Die size 200 mm, die gap 2,7 mm. This product is not intended for and must not be used in any pharmaceutical/medical applications. AmericasAsiaEuropeGreater ChinaMEA
Density 926 kg/m3, MFR (2.16 kg) 0.7 g/10 min SABIC® LLDPE 726NE is a butene linear low density polyethylene resin. This grade is designed to give blown films a relatively high stiffness for good machinability and a good overall balance of other performance properties, such as puncture resistance, impact strength and heat sealability. Application Typical applications for SABIC® LLDPE 726NE are shipping sacks, produce bags, can liners and carrier bags. SABIC® LLDPE 726NE has very good optical properties when blended with a LDPE (15-85%). Film properties Film of 50 μm and BUR=2 has been produced on Kiefel IBC with 130 kg/h. Die size 200 mm, die gap 2,7 mm. This product is not intended for and must not be used in any pharmaceutical/medical applications. AmericasAsiaEuropeGreater ChinaMEA
Density 925 kg/m3, MFR (2.16 kg) 0.7 g/10 min SABIC® LLDPE 726NJ is a butene linear low density polyethylene resin. This grade is typically designed to give blown films a relatively high stiffness for good machinability and a good overall balance of other performance properties, such as puncture resistance, impact strength and heat sealability. The grade is TNPP free. Typical applications for SABIC® LLDPE 726NJ are shipping sacks, produce bags, can liners and carrier bags. SABIC® LLDPE 726NJ has good optical properties when blended with a LDPE (15-85%). Film properties: Film of 50 µm and BUR=2 has been produced on Kiefel IBC with 130 kg/h. Die size 200 mm, die gap 2,7 mm. This product is not intended for and must not be used in any pharmaceutical/medical applications. AmericasAsiaEuropeGreater ChinaMEA
726Q Linear low density polyethylene 726Q Linear low density polyethylene AmericasAsiaEuropeGreater ChinaMEA
Density 926 kg/m3, MFR (2.16 kg) 0.7 g/10 min SABIC® LLDPE 726QE is a butene linear low density polyethylene resin. This grade is designed to give blown films a relatively high stiffness for good machinability and a good overall balance of other performance properties, such as puncture resistance, impact strength and heat sealability. This material contains anti block, slip agent and processing aid. Application Typical applications for SABIC® LLDPE 726QE are shipping sacks, produce bags, can liners and carrier bags. SABIC® LLDPE 726QE has very good optical properties when blended with a LDPE (15-85%). Film properties Film of 50 μm and BUR=2 has been produced on Kiefel IBC with 130 kg/h. Die size 200 mm, die gap 0.8 mm. This product is not intended for and must not be used in any pharmaceutical/medical applications. AmericasAsiaEuropeGreater ChinaMEA
726QJ Linear low density polyethylene 726QJ Linear low density polyethylene AmericasAsiaEuropeGreater ChinaMEA
Density 920 kg/m3, MFR(2.16 kg) 0.85 g/10 min SABIC® 920NT is an ethylene-butene copolymer designed for blown film application. Excellent mechanical strength, tear and puncture resistance. 920NT contains no slip and no antiblock. Asia
Density 926 kg/m3, MFR(2.16 kg) 0.85 g/10 min SABIC® 926NT is an ethylene-butene copolymer designed for blown film application. Excellent mechanical strength, tear and puncture resistance, 926NT contains no slip and no antiblock. Asia
Density 924 kg/m3, MFR(2.16 kg) 13 g/10 min SABIC® M13024T is a Linear Low Density Polyethylene grade for injection molding applications. It has been designed to give good flow properties with low temperature toughness, stress crack resistance and high gloss. Asia
Density 924 kg/m3, MFR(2.16 kg)20 g/10 min SABIC® LLDPE M200024 is a linear low density polyethylene copolymer injection moulding grade with a narrow molecular weight distribution. It has been typically designed to have good low temperature toughness, stress crack resistance (ESCR) and gloss. AmericasAsiaEuropeGreater ChinaMEA
Density 924 kg/m3, MFR(2.16 kg) 20 g/10 min SABIC® M200024T is a Linear Low Density Polyethylene grade for injection molding applications. It has been designed to give good flow properties with low temperature toughness, stress crack resistance and high gloss. Asia
Density 926 kg/m3, MFR(2.16 kg) 50 g/10 min M500026 is a Linear Low Density Polyethylene grade with narrow molecular weight distribution suitable for injection molding applications. It has been designed to give excellent flow properties with better low temperature toughness, stress crack resistance and gloss. AmericasAsiaEuropeGreater ChinaMEA
Density 922 kg/m3, MFR(2.16 kg) 5 g/10 min SABIC® M50022T is a Linear Low Density Polyethylene grade for injection molding applications. It has been designed to give good flow properties with low temperature toughness, stress crack resistance and high gloss. Asia
Density 926 kg/m3, MFR(2.16 kg) 50 g/10 min SABIC®M550027T is a Linear Low Density Polyethylene grade with narrow molecular weight distribution suitable for injection molding applications. It has been designed to give excellent flow properties with better low temperature toughness, stress crack resistance and gloss. Asia
Density 924 kg/m3, MFR(2.16 kg) 20 g/10 min SABIC® LLDPEMG200024 is a high flow linear low density polyethylene copolymer grade with a narrow molecular weight distribution. SABIC® LLDPE MG200024 is in powder form. AmericasAsiaEuropeGreater ChinaMEA
Density 926 kg/m3, MFR(2.16 kg) 50 g/10 min SABIC® LLDPE MG50026 is a high flow Linear Low Density Polyethylene grade with a narrow molecular weight distribution. SABIC® LLDPE MG500026 resin is in powder form and is designed to give excellent flow properties with better low temperature toughness, stress crack resistance and gloss. AmericasAsiaEuropeGreater ChinaMEA
Density 918 kg/m3, MFR(2.16 kg) 1.0 g/10 min P118 is a natural linear low density polyethylene (LLDPE) resin, designed for non-pressure pipe extrusion application. AmericasAsiaEuropeGreater ChinaMEA
Density 918 kg/m3, MFR(2.16 kg) 2.0 g/10 min P218 is a natural linear low density polyethylene (LLDPE) resin, designed for non-pressure pipe extrusion application. AmericasAsiaEuropeGreater ChinaMEA
Density 938 kg/m3, MFR(2.16 kg) 0.4 g/10 min P438J is a Medium Density Polyethylene natural resin and TNPP free designed for extrusion applications. This grade combines stiffness, toughness, high melt strength and low gel content coupled to excellent processability due to its tailored molecular weight distribution and flow properties. It contains an optimized level of stabilizers and is free from any slip or anti-block additives. AmericasAsiaEuropeGreater ChinaMEA
Density 918 kg/m3, MFR(2.16 kg) 0.9 g/10 min SABIC® LLDPE PCG61 is a hexene-linear low density polyethylene typically used for healthcare applications. Films made from this resin exhibit good mechanical, optical and hottack properties. Typical application for SABIC® LLDPE PCG61 are pharmaceutical films, bags and pouches requiring good impact strength, tear resistance,optical performance andhottack properties. Film properties: Film of 50 µm and BUR = 2 has been produced on Kiefel IBC with 140 kg/h. Die size 200 mm, die gap 2.7 mm. Compliance to RegulationsSABIC® LLDPE PCG61 complies with the relevant monographs of the European Pharmacopoeia (EP) and the United States Pharmacopoeia (USPVI). AmericasAsiaEuropeGreater ChinaMEA
Density 937 kg/m3, MFR (2.16 kg) 3.5 g/10 min SABIC® LLDPE R40039EE is a medium density polyethylene (MDPE) copolymer. It is used for its good stress crack resistance, rigidity, gloss and low warpage. The resin contains UV-stabilizer. It is recommended that SABIC® LLDPE R40039E is grinded before use in rotational moulding applications. Typical applications. Because of the good processing performance and physical properties, SABIC® LLDPE R40039EE is used for the rotational moulding of large industrial and agricultural tanks, trash containers and chemical shipping drums. Due to the good mechanical properties and low warpage this product is typically used for injection moulding of screw closures, caps and housewares. The UV-stabilization provides good protection for the final product. Processing conditions. Moulding cycles vary with mould composition and mould wall thickness, oven temperature and wall thickness of the part being produced. Venting of the mould is recommended. Normal cooling is satisfactory for SABIC®LLDPE R40039EE. Oven temperature °F (°C) = 600 (315). Typical processing temperature for injection moulding machines: 210 - 240 °C. Mechanical properties. Test specimens are prepared from compression moulded sheet made according to ASTM D-1928, procedure C. This product is not intended for and must not be used in any pharmaceutical/medical applications. AmericasAsiaEuropeGreater ChinaMEA
Density 935 kg/m3, MFR(2.16 kg) 5 g/10 min R50035 is a Linear Low Density Polyethylene grade with balanced density and viscosity designed to provide excellent stress cracking resistance, good mechanical properties with high rigidity, toughness, and low warpage. R50035 is a non-UV stabilized grade in pellet form AmericasAsiaEuropeGreater ChinaMEA
Density 935 kg/m3, MFR(2.16 kg) 5 g/10 min R50035E is a Linear Low Density Polyethylene grade with balanced density and viscosity designed to provide excellent stress cracking resistance, good mechanical properties with high rigidity, toughness, and low warpage. R50035E is an antioxdant and UV stabilized grade in pellet form. AmericasAsiaEuropeGreater ChinaMEA
Density 933 kg/m3, MFR(2.16 kg) 5 g/10 min SABIC® LLDPE R50035EE is a LLDPE copolymer that provides good stress crack resistance, rigidity, toughness, gloss and very low warpage. The resin contains UV stabilizer. It is recommended that SABIC® LLDPE R50035EE is grinded before use in rotational moulding applications. Typical Applications. SABIC® LLDPE R50035EE is used for rotational moulding of large industrial and agricultural tanks, trash containers and chemical shipping drums. Because of its good mechanical properties and low warpage, it is used for injection moulding of screw closures, caps and housewares. SABIC® LLDPE R50035EE is UV stabilised; which provides good protection for the final product. Processing conditions. Oven temperature °C (°F) = 315 (600) Typical processing temperature for injection moulding machines: 210 - 240 °C. Mechanical properties. Test specimens are prepared from compression moulded sheet made according to ASTM D-1928, procedure C. This product is not intended for and must not be used in any pharmaceutical/medical applications. AmericasAsiaEuropeGreater ChinaMEA
Density 935 kg/m3, MFR(2.16 kg) 5 g/10 min RG50035 is a Linear Low Density Polyethylene grade with balanced density and viscosity designed to provide excellent stress cracking resistance, good mechanical properties with high rigidity, toughness, and low warpage. RG50035 is a non-UV stabilized reactor powder grade. AmericasAsiaEuropeGreater ChinaMEA